is a family of networking technologies that are defined in the IEEE 802.2 and 802.3 standards and operate at the data link layer of the OSI model.
In ________________ switching, when the switch receives the frame, it stores the data in buffers until the complete frame has been received.
The __________________________ defines the processing capabilities of a switch by rating how much data the switch can process per second.
Ethernet standards define both the Layer 2 protocols and the Layer 1 technologies.
Which field in an Ethernet frame is used for error detection?
Which of the following Ethernet changes occurred in the year 2002?
On a Windows PC, what command is used to display the ARP table?
In ________________ switching, the switch stores the first 64 bytes of the frame before forwarding.
What happens when an Ethernet frame is less than 64 bytes in length?
What allows different data rates on different switch ports?
Which standard specifies the Ethernet MAC sublayer functionality in a computer NIC?
What feature is used on a switch to automatically detect the required cable type for copper Ethernet connections and configure the interfaces accordingly?
Whether a packet is destined for a local host or a remote host is determined by the IP address and subnet mask combination of the source device compared to the IP address of the destination device.
The last 2 bits of the Differentiated Services field of an IPv4 header identify the explicit congestion notification (ECN) value that can be used to prevent dropped packets during times of network congestion.
What is the IP address of the local default route?
The local routing table of a host typically contains a route to the loopback interface (127.0.0.1). This address is known as a
What command is used on a Cisco IOS router to display the routing table of the router?
When entering the route print command, the Interface List section displays which of the following?
Which part of an IPv4 packet contains the Layer 4 segment information and the actual data?
A routing table on a router stores information about both directly connected and remote routes. The route source field in the table identifies how the route was learned. Which code identifies that a route was learned dynamically from another router using the Enhanced Interior Gateway Routing Protocol (EIGRP)?
IP is connectionless, meaning that no dedicated end-to-end connection is created before data is sent.
The default route is only used when a host must forward packets to a remote network.
In IPv6, what is equivalent to the IPv4 loopback address?
When using the netstat –r command on a host, you see a route 0.0.0.0 0.0.0.0. What does this route represent?
Which of the following is not a column in an IPv6 Route Table?
Set 2
______________ is a physical port on a Layer 3 switch configured to act as a router port.
In ___________________ buffering, frames are stored in queues that are linked to specific incoming and outgoing ports.
Which standard specifies the Ethernet MAC sublayer functionality in a computer NIC?
In Ethernet technology, IP addresses are used to identify the frame source and destination.
In cut-through switching, the switch does not perform any error checking on the frame.
The ______________ sublayer of the data link layer is responsible for the placement of frames on the media and the removal of frames from the media.
________________ allows a switch to deliver power to a device, such as IP phones and some wireless access points, over the existing Ethernet cabling.
Which of the following Ethernet changes occurred in the year 2002?
MAC addresses are displayed as ___________________ numbers.
Which of the following is not one of the primary fields in an Ethernet frame?
If a destination host is not on the local network, the source node uses the MAC address of the ___________________ as the destination address in its frames.
Ethernet is a contention-based method of networking that provides a method for controlling how the nodes share access to the medium through the use of __________________ technology.
Which part of an IPv4 packet contains the Layer 4 segment information and the actual data?
The role of a ________________ is to select paths for and direct packets toward the destination host in a process called ___________________.
The Internet is largely based on _____, which is still the most widely used network layer protocol.
The local routing table of a host typically contains a route to the loopback interface (127.0.0.1). This address is known as a ______________________.
After header information is added to a PDU by the network layer, the PDU is called a ______________.
What does the version field of an IPv6 header always contain to identify IPv6 packets?
Which of the following is not an advantage of the IPv6 simplified header over the IPv4 header?
When entering the route print command, the Interface List section displays which of the following?
Which field in an IPv4 header is used for error checking of the IP header?
A router’s IOS is typically stored in flash memory and is copied into RAM for execution by the CPU during bootup.
Which of the following is not a column in an IPv6 Route Table?
What is the IPv6 equivalent of the local default route?
On a router, what field in an IPv4 header should be examined to determine that the maximum number of hops has been reached by the packet on its way from the source to the destination?